扫把佬有一根 $363.30AUD 的线~ 的确很无语 www.6park.com
其实，DIY的话基本上不需要花一分钱~ 呵呵 www.6park.com
1. 今天的主角：E46 M3 www.6park.com
 www.6park.com

里面~ www.6park.com
 www.6park.com

2. 首先从乘客边的饰条拆起，要水平拔出~ 要费好大的劲才可以哦~ www.6park.com
 www.6park.com

3. 拆掉饰条之后的样子 www.6park.com
 www.6park.com

4. 饰条的背后就是用这些钉子固定的了~ www.6park.com
 www.6park.com

5. 然后拆CD机上面的饰条~ www.6park.com
 www.6park.com
 www.6park.com
6.不需要全部拆下来，够得着螺丝就可以了 www.6park.com
 www.6park.com

7. www.6park.com
 www.6park.com

8. CD机很快就抽出来了~ www.6park.com
 www.6park.com

9. CD机底部的样子 www.6park.com
 www.6park.com

10.  www.6park.com
 www.6park.com

11. CD 机后面的插座（Female） 注意上面标有编号的，我们要用右下角的那个插头，针脚定义：Pin 4=ground, pin 8=right and pin 9=left。 
到时候只要有输入讯号，CD机便会自动让你选择AUX mode。 www.6park.com
 www.6park.com
 www.6park.com
12. 这是CD机后面的插头，插的超紧的~ 而且有扣具，拆的时候不能急 www.6park.com
 www.6park.com
 www.6park.com
13.还需要拆一样东西：烟灰缸 www.6park.com
 www.6park.com
 www.6park.com
14. 到时候我就会把AUX的插头放在这个洞里面，本来是给你塞烟头用的~ www.6park.com
 www.6park.com
 www.6park.com
15. 背面~ 可以看到是一片金属里面安了个圆锥形的塑料~ 简直是为我而设 www.6park.com
 www.6park.com
 www.6park.com
16. www.6park.com
 www.6park.com
 www.6park.com
17. 而且，烟灰缸旁边还有个洞，方便我走线~ www.6park.com
 www.6park.com
 www.6park.com
准备工作到此结束，剩下的移师室内进行~
------------------------------------------------------------------ www.6park.com

18. 材料一：小转大 耳机转换头~ 因为它有3.5mm 的Female 口~  www.6park.com
 www.6park.com

19.材料二：旧电脑上拆下来的线~ 主要是电源开关、LED灯之类的线。 www.6park.com
 www.6park.com
 www.6park.com
20. 电脑线插头特写 www.6park.com
 www.6park.com

21. 动工~ 把耳机头尾巴切了，长度刚好小于烟灰缸的高度一点就可以 www.6park.com
 www.6park.com
 www.6park.com
22. 然后把塞烟头的那个圆锥形塑料拆出来 www.6park.com
 www.6park.com
 www.6park.com
23. 用刀子画个圈圈，然后把尾巴切了~ 主要是要开个口放耳机转换头。 www.6park.com
 www.6park.com

24.用热熔胶把那个耳机头粘上去先~ www.6park.com
 www.6park.com
 www.6park.com
25. 看看靓仔不~ www.6park.com
 www.6park.com

26.然后分别焊上三条线：Ground, Left, Right www.6park.com
 www.6park.com

27. 再用热熔胶滴下去，把整个插头密封起来~  www.6park.com
 www.6park.com

28. 模仿一下插上AUX线的样子吧~  www.6park.com
 www.6park.com

29. 装回烟灰缸里面去~ www.6park.com
 www.6park.com
 www.6park.com
30. 线的另一头就可以查到CD机背后了~ 针脚定义：Pin 4=ground, pin 8=right and pin 9=left。 www.6park.com
 www.6park.com

----------------------------- www.6park.com
到现在为止还算简单是吧~ 哈哈~ 那么我们回到车里面，把他们装回去看看吧~！ www.6park.com
----------------------------- www.6park.com

31. 中控台能拆的都要拆掉~ www.6park.com
 www.6park.com

32. 先从波棍拆起 www.6park.com
 www.6park.com

33. 再把烟灰缸的座拆出来，把线伸进去 www.6park.com
 www.6park.com

34. 烟灰缸放回去了~ www.6park.com
 www.6park.com

35. 冷气面板是要拆的，方便走线
这样线就很容易穿上来了~ www.6park.com
 www.6park.com

36. 按照刚才说的，把地线、左右极插上~ 这电脑线本身就有个扣，可以插牢。 www.6park.com
 www.6park.com

37. 插上音源测试： 马上弹出了AUX mode 了~ ye~ www.6park.com
 www.6park.com
 www.6park.com
38. 把Balance 推到最右边~ 看看正常不~ 然后在测试左边~ 结果完美！ www.6park.com
 www.6park.com

39. 然后把冷气控制面板装回去~ www.6park.com
 www.6park.com

40. www.6park.com
 www.6park.com
 www.6park.com
41.波棍盖子~ www.6park.com
 www.6park.com
 www.6park.com
42. 再看看改装过的烟灰缸 www.6park.com
 www.6park.com
 www.6park.com
43. 把螺丝拧好~ 饰条装装上~ 便大功告成 www.6park.com
 www.6park.com
 www.6park.com
44. www.6park.com
 www.6park.com
 www.6park.com
45 www.6park.com
 www.6park.com
 www.6park.com
46. www.6park.com
 www.6park.com
 www.6park.com
 www.6park.com

再送几张图给大家，谢谢捧场 www.6park.com
47. www.6park.com
 www.6park.com

48. www.6park.com
 www.6park.com
 www.6park.com
49. www.6park.com
 www.6park.com
 www.6park.com
50. www.6park.com
 www.6park.com
 www.6park.com
51. www.6park.com
 www.6park.com
 www.6park.com
52. www.6park.com
 www.6park.com
 www.6park.com
53. www.6park.com
 www.6park.com
 www.6park.com
54. www.6park.com
 www.6park.com
 www.6park.com

55~ End~~~ www.6park.com
 www.6park.com
 www.6park.com